STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

Slope stability to EN 1997-1

A 10 m high slope at 1 : 2 in one soil layer. Here the factor of safety of the critical slip circle is worked by hand with Bishop's simplified method of slices, then checked for overall stability to EN 1997-1 Design Approach 1. The hand calculation is checked against the STATIX slope stability calculator.

1. The problem

InputValue
Slopeheight H = 10 m at 1 : 2 (vertical : horizontal), 26.6°
Ground15 m flat in front of the toe, 20 m flat crest behind the slope
Firm base10 m below the toe (no slip below it)
Soilone layer: c′ = 5 kPa, φ′ = 28°, γ = 19 kN/m³
Water, surchargenone (dry), no surcharge
MethodBishop simplified, circular slips
Target F1.5 (practice value)

2. The method Bishop simplified (Bishop 1955)

A circular block of soil is cut into vertical slices. The factor of safety F is the shear strength along the slip circle divided by the shear stress needed for equilibrium, taken as moments about the circle centre. Bishop's simplified method also takes vertical equilibrium of each slice, with the forces between slices horizontal. F then appears on both sides, so it is found by iteration. This is the method the calculator uses by default; EN 1997-1 section 11 asks for the overall stability check; Bishop's method is one of the usual ways to make it.

F = Σ [ (c′ b + (W − u b) tan φ′) / m_α ] / Σ W sin α m_α = cos α + sin α tan φ′ / F (here dry: u = 0)

3. The critical circle slip search

This step is NOT worked by hand: the critical circle is taken from the calculator, which tries 18 396 circles (a grid of centres and radii, two finer grids around the best one, then a pattern search) and keeps the one with the lowest F. No one does that search on paper. Every step after this one is worked by hand for that one circle. A quick check: the circle passes through the toe, and it meets the crest level y = 10 m at:

centre (x_c, y_c) = (15.182, 27.364) m, R = 27.365 m distance centre to toe = √((15 − 15.182)² + 27.364²) = 27.365 m = R (a toe circle) crest exit x = x_c + √(R² − (y_c − 10)²) = 15.182 + √(27.365² − 17.364²) = 36.332 m
firm base, 10 m below the toecentre (15.18, 27.36), R = 27.36 mtoe (15, 0)crestF = 1.5191 : 2

4. Slice weights

The block between the toe (x = 15 m) and the crest exit (x = 36.332 m) is cut into 12 slices: 10 slices 2 m wide on the slope face and 2 on the crest. Each slice weight is γ b h, with h the height from the slip circle to the ground at the slice centre. α is the slope of the slip circle under the slice; sin α = (x − x_c) / R. One slice in full, then all of them:

slice 6: x = 26.000 m, b = 2.000 m ground y = (26.000 − 15) / 2 = 5.500 m slip base y = 27.364 − √(27.365² − (26.000 − 15.182)²) = 2.229 m h = 5.500 − 2.229 = 3.271 m, W = γ b h = 19 × 2.000 × 3.271 = 124.32 kN/m sin α = (x − x_c) / R = (26.000 − 15.182) / 27.365 = 0.3953, cos α = 0.9185 # x (m) b (m) h (m) W (kN/m) sin α cos α W sin α 1 16.000 2.000 0.488 18.56 0.0299 0.9996 0.55 2 18.000 2.000 1.355 51.49 0.1030 0.9947 5.30 3 20.000 2.000 2.073 78.78 0.1761 0.9844 13.87 4 22.000 2.000 2.638 100.23 0.2492 0.9685 24.97 5 24.000 2.000 3.041 115.55 0.3222 0.9467 37.24 6 26.000 2.000 3.271 124.32 0.3953 0.9185 49.15 7 28.000 2.000 3.313 125.89 0.4684 0.8835 58.97 8 30.000 2.000 3.141 119.37 0.5415 0.8407 64.64 9 32.000 2.000 2.722 103.45 0.6146 0.7888 63.58 10 34.000 2.000 2.003 76.12 0.6877 0.7260 52.34 11 35.333 0.666 1.150 14.55 0.7364 0.6766 10.71 12 35.999 0.666 0.398 5.03 0.7607 0.6491 3.83 Σ W sin α = 385.16 kN/m

5. The Bishop iteration Bishop simplified

With c′ = 5 kPa and tan φ′ = tan 28° = 0.5317, each slice gives c′ b + W tan φ′, divided by m_α. Start with a guess F = 1.5, work out m_α for every slice, add the terms and divide by Σ W sin α. That gives a new F; repeat until F stops changing. Here: F = 1.5000 → 1.5163 → 1.5186 → 1.5189 → 1.5190. The table is the last round:

# c′b + W tan φ′ m_α term 1 19.87 1.0100 19.67 2 37.38 1.0307 36.27 3 51.89 1.0460 49.60 4 63.29 1.0557 59.95 5 71.44 1.0595 67.43 6 76.10 1.0569 72.00 7 76.94 1.0475 73.45 8 73.47 1.0302 71.31 9 65.01 1.0040 64.75 10 50.47 0.9667 52.21 11 11.06 0.9343 11.84 12 6.00 0.9154 6.56 Σ = 585.05 kN/m F = 585.05 / 385.16 = 1.5190

6. How many slices

Twelve slices are enough by hand. The same sums with 426 slices (as the calculator uses for the critical circle) give F = 1.5189. The difference is in the fourth decimal: the slice count does not change the answer here.

F (12 slices) = 1.5190 F (426 slices) = 1.5189

7. Against the target practice value

There is no code value for a characteristic factor of safety. F ≥ 1.5 for a permanent slope is a common practice value (the calculator's default target, which you can change); it is not a code number.

F = 1.519 ≥ 1.5 OK

8. Overall stability to EN 1997-1 EN 1997-1 2.4.7.3.4, 11; Annex A Table A.4

The code check uses Design Approach 1, Combination 2: the soil strengths are divided by the M2 factors γc′ = γφ′ = 1.25 (a variable surcharge would be multiplied by 1.3, but there is none here), and the design Fd must be at least 1.0. The calculator searches again with the design strengths and finds the same circle. With both c′ and tan φ′ divided by the same 1.25, every term divides by 1.25 and m_α stays the same, so Fd = F / 1.25 exactly:

c′_d = 5 / 1.25 = 4.0 kPa, tan φ′_d = 0.5317 / 1.25 = 0.4254 F_d = 1.5190 / 1.25 = 1.2152 ≥ 1.0 OK

9. The calculator's answer

The calculator, with the same inputs, gives F = 1.518 and Fd = 1.215 (engine 1.1.1, Bishop simplified; it shows a factor of safety rounded down, so it never reads above the true value). The hand calculation with 12 slices gives 1.519 and 1.215. Add a water table 4 m below the crest in the calculator and see how much F drops.

hand (12 slices): F = 1.5190, F_d = 1.2152 calculator: F = 1.5189, F_d = 1.2151 (PASS)
Run this example yourselfOpen the STATIX slope stability calculator. These are the calculator's default inputs, so it opens on this example. Change any value and the result updates, with every check and a calc sheet.
Open the slope stability calculator

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.

Early access

Be first to use STATIX 3D.

STATIX 3D is still being built. Join the early-access list and we will tell you when it is ready for testing. One confirmation now, one message then.

Get early access