STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

Section properties of a solid rectangle

Every member check starts from the section properties. Here they are worked by hand for a 300 × 500 mm solid rectangle: A, I, r, Wel, Wpl, J, the mass and the shear stress. The hand calculation is checked against the STATIX section properties calculator.

1. The problem

InputValue
Shapesolid rectangle
Width b300 mm (horizontal)
Depth h500 mm (vertical)
Steel f_y355 MPa (for ε and the class only)
Density ρ7850 kg/m³ (for the mass)
Shear V100 kN (for the shear stress)

2. The axes EN 1993 axis names

The calculator uses the EN 1993 names: y-y is the strong (major) axis, here the horizontal axis through the centroid, and z-z is the weak (minor) axis, the vertical one (SANS 10162-1 calls them x-x and y-y). For a solid rectangle the centroid is at the middle: b / 2 and h / 2 from the bottom-left corner.

A = b h = 300 × 500 = 150000 mm² centroid: y = 300 / 2 = 150.0 mm, z = 500 / 2 = 250.0 mm (from the bottom-left corner)
yzb = 300 mmh = 500 mmτ max = 1.00 MPashear stress, V = 100 kN

3. Second moments of area

The second moment of area, I = ∫ z² dA, measures the bending stiffness of the shape. For a rectangle about its own centroid it is the width times the cube of the depth over 12. The depth counts as a cube, which is why the section is stiffer about y-y.

I_y = b h³ / 12 = 300 × 500³ / 12 = 3125.0 × 10⁶ mm⁴ I_z = h b³ / 12 = 500 × 300³ / 12 = 1125.0 × 10⁶ mm⁴

4. Radii of gyration

The radius of gyration r = √(I / A) is the distance at which the whole area would give the same I. It is what a column buckling check uses for slenderness (L / r).

r_y = √(3125.0 × 10⁶ / 150000) = 144.34 mm r_z = √(1125.0 × 10⁶ / 150000) = 86.60 mm

5. Elastic section moduli

The elastic modulus Wel = I / c, with c the distance from the axis to the outermost fibre, gives the moment at which that fibre first reaches yield: M = Wel fy. For a rectangle it is b h² / 6.

W_el,y = I_y / (h / 2) = 3125.0 × 10⁶ / 250.0 = 12.5000 × 10⁶ mm³ (= b h² / 6) W_el,z = I_z / (b / 2) = 1125.0 × 10⁶ / 150.0 = 7.5000 × 10⁶ mm³ (= h b² / 6)

6. Plastic section moduli and the shape factor

When the whole section has yielded, the stress is fy in tension on one side of the plastic neutral axis and fy in compression on the other. That axis halves the area; for a rectangle it is the centroidal axis. Wpl is the sum of each half's area times the distance of its centroid from that axis: (b h / 2) × (h / 4) × 2 = b h² / 4. The ratio Wpl / Wel is the shape factor, 1.5 for every solid rectangle.

W_pl,y = b h² / 4 = 300 × 500² / 4 = 18.7500 × 10⁶ mm³ W_pl,z = h b² / 4 = 500 × 300² / 4 = 11.2500 × 10⁶ mm³ shape factor = W_pl,y / W_el,y = 18.7500 / 12.5000 = 1.500

7. Torsion constant St Venant torsion, Roark

A solid rectangle does not twist like a round bar: its torsion constant J is less than the polar moment Iy + Iz. The calculator uses the closed form for a solid rectangle given by Roark, with b the short side and d the long side. A solid section has no warping worth counting, so Cw = 0.

b / d = 300 / 500 = 0.6, b⁴ / (12 d⁴) = 0.0108 J = b³ d [1/3 − 0.21 (b / d)(1 − b⁴ / (12 d⁴))] = 300³ × 500 × [0.333333 − 0.21 × 0.6 × (1 − 0.0108)] = 13.5 × 10⁹ × 0.208694 = 2.8174 × 10⁹ mm⁴ (the polar moment I_y + I_z = 4.2500 × 10⁹ mm⁴, for comparison)

8. Mass

The mass per metre is the area times the density. The density is the page's default, 7850 kg/m³ for steel; for concrete or timber change it.

mass = A ρ = 0.150 m² × 7850 kg/m³ = 1177.5 kg/m

9. Shear stress under V = 100 kN EN 1993-1-1 cl 6.2.6; τ = V Q / (I t)

The elastic shear stress at a level is V Q / (I t), with Q the first moment about the neutral axis of the area beyond that level and t the width there. It is largest at the neutral axis, where Q is the first moment of the top half: (b h / 2) × (h / 4). For a rectangle that gives 1.5 times the average V / A. EN 1993-1-1 6.2.6(3) has no shear area for a solid bar; the calculator takes the whole area, Av = A.

Q = b (h / 2)(h / 4) = 300 × 250.0 × 125.0 = 9.375 × 10⁶ mm³ τ_max = V Q / (I_y b) = 100000 × 9.375 × 10⁶ / (3125.0 × 10⁶ × 300) = 1.000 MPa τ_avg = V / A_v = 100000 / 150000 = 0.667 MPa (τ_max / τ_avg = 1.50)

10. Classification EN 1993-1-1 Table 5.2

Class 1 to 4 (EN 1993-1-1 Table 5.2) describes local buckling of the thin plates of a steel section: their width-to-thickness ratios against limits in ε = √(235 / fy). A solid rectangle has no thin plates, so local buckling does not apply and the calculator reports Class 1. ε is shown for completeness.

ε = √(235 / 355) = 0.814 solid section: Class 1 (local buckling not applicable)

11. The calculator's answer

The calculator, with the same inputs, gives the same numbers (engine section-properties-engine.js, git 6db81e87; the engine has no version number of its own). The shape factor of 1.5 tells you that a solid rectangle has 50 % more bending strength after first yield; an I section has about 1.1 to 1.2. Try an I section in the calculator and compare Iy per kilogram.

hand: A = 150000 mm², I_y = 3125.0 × 10⁶ mm⁴, W_pl,y = 18.7500 × 10⁶ mm³, J = 2.8174 × 10⁹ mm⁴, τ_max = 1.000 MPa calculator: A = 150000 mm², I_y = 3125.0 × 10⁶ mm⁴, W_pl,y = 18.7500 × 10⁶ mm³, J = 2.8174 × 10⁹ mm⁴, τ_max = 1.000 MPa, Class 1
Run this example yourselfOpen the STATIX section properties calculator. These are the calculator's default inputs (Rectangle, 300 × 500 mm, fy 355 MPa, ρ 7850 kg/m³, V 100 kN), so it opens on this example. Change any value and the result updates, with every check and a calc sheet.
Open the section properties calculator

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.

Early access

Be first to use STATIX 3D.

STATIX 3D is still being built. Join the early-access list and we will tell you when it is ready for testing. One confirmation now, one message then.

Get early access