STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

RC section stresses and crack width to EN 1992-1-1

A cracked RC section must keep its stresses and its crack width within the limits of EN 1992-1-1 section 7. Here the cracked elastic section and the crack width formula of 7.3.4 are worked by hand for a 300 × 500 mm beam section with three Y20 bars. The hand calculation is checked against the STATIX RC section SLS calculator.

1. The problem

InputValue
Sectionrectangle b × h = 300 × 500 mm
Bottom bars3 Y20, centres 50 mm above the soffit
Top bars2 Y12, centres 450 mm above the soffit
Concrete / steelf_ck = 30 MPa, f_yk = 500 MPa, E_s = 200 GPa
Moments (N = 0)characteristic M = 120 kNm, quasi-permanent M = 90 kNm (sagging)
ExposureXC
Creep, cover, spacingφ = 2, c = 35 mm, bar spacing 100 mm
Crack width limitw_max = 0.3 mm

2. The method EN 1992-1-1 7.2, 7.3.4

At the serviceability limit state the concrete and the steel are taken as linear elastic. Once the concrete tension passes fctm, the section is cracked and the concrete below the neutral axis carries nothing. Two load cases are checked: the characteristic moment (stress limits of 7.2(2) and 7.2(5)) and the quasi-permanent moment (the creep limit of 7.2(3) and the crack width of 7.3.4). For the long-term quasi-permanent case the concrete modulus is reduced for creep.

3. Materials EN 1992-1-1 Table 3.1, 7.4.3(5)

Ecm and fctm come from Table 3.1. The effective modulus for long-term load is Ecm / (1 + φ). The modular ratio αe = Es / Ec turns steel area into equivalent concrete area. φ = 2.0 is the calculator's default creep coefficient: a practice value: work out φ for your own member (age at loading, humidity, size).

f_cm = 30 + 8 = 38 MPa E_cm = 22000 × (38 / 10)^0.3 = 32836.6 MPa f_ctm = 0.3 × 30^(2/3) = 2.896 MPa E_c,eff = 32836.6 / (1 + 2) = 10945.5 MPa α_e (characteristic) = 200000 / 32836.6 = 6.091 α_e (quasi-permanent) = 200000 / 10945.5 = 18.272

4. Is the section cracked?

First the whole section is assumed to work (uncracked), with the bars counted as (αe − 1) As of extra concrete. If the bottom tension is above fctm, the section cracks. As1 = 3 × π × 20² / 4 = 942.5 mm² (bottom), As2 = 2 × π × 12² / 4 = 226.2 mm² (top).

characteristic: A = 155949 mm², centroid 245.32 mm above the soffit, I = 3359.6 × 10^6 mm^4 σ_bottom = M y / I = 120 × 10^6 × 245.32 / (3359.6 × 10^6) = 8.76 MPa > f_ctm 2.90 MPa → cracked quasi-permanent: A = 170186 mm², centroid 235.46 mm, I = 3896.5 × 10^6 mm^4 σ_bottom = 90 × 10^6 × 235.46 / (3896.5 × 10^6) = 5.44 MPa > 2.90 MPa → cracked

5. Cracked neutral axis, characteristic

With N = 0 the neutral axis is where the first moment of the transformed cracked section is zero: the compression concrete (b x) and the top bars (αe As2) above it balance the bottom bars (αe As1) below it. The depths from the top are d = 450 mm and d2 = 50 mm. That gives a quadratic in x:

(b/2) x² + α_e (A_s1 + A_s2) x − α_e (A_s1 d + A_s2 d2) = 0 150 x² + 7118.1 x − 2652072 = 0 x = (−7118.1 + √(7118.1² + 2 × 300 × 2652072)) / 300 = 111.34 mm

6. Stresses, characteristic EN 1992-1-1 7.2(2), 7.2(5)

The cracked second moment of area Icr about the neutral axis gives the stresses by M y / I, times αe for the steel. The 0.6 fck limit of 7.2(2) is required only in XD, XF and XS exposure; this example is XC, so it is shown for information. The steel limit 0.8 fyk of 7.2(5) applies always.

I_cr = b x³/3 + α_e A_s2 (x − d2)² + α_e A_s1 (d − x)² = 300 × 111.34³/3 + 6.091 × 226.2 × 61.34² + 6.091 × 942.5 × 338.66² = 801.6 × 10^6 mm^4 σ_c = M x / I_cr = 120 × 10^6 × 111.34 / (801.6 × 10^6) = 16.67 MPa ≤ 0.6 × 30 = 18.0 MPa (for information, XC) σ_s1 = α_e M (d − x) / I_cr = 6.091 × 120 × 10^6 × 338.66 / (801.6 × 10^6) = 308.8 MPa ≤ 0.8 × 500 = 400 MPa OK σ_s2 = α_e M (x − d2) / I_cr = 55.9 MPa (compression)

7. Neutral axis and stresses, quasi-permanent EN 1992-1-1 7.2(3)

The same two steps with the long-term αe = 18.272. The softer concrete pushes the neutral axis down. Below 0.45 fck creep can be taken as linear (7.2(3)).

150 x² + 21354.3 x − 7956217 = 0 → x = 169.88 mm I_cr = 1901.0 × 10^6 mm^4 σ_c = 90 × 10^6 × 169.88 / (1901.0 × 10^6) = 8.04 MPa ≤ 0.45 × 30 = 13.50 MPa OK σ_s1 = 18.272 × 90 × 10^6 × 280.12 / (1901.0 × 10^6) = 242.33 MPa, σ_s2 = 103.7 MPa (compression)
x = 169.9 mmσc 8.04 MPaσs 242.3 MPaσs2 103.7 MPa (comp.)3Y20 at 50, 2Y12 at 450 mm from the soffit

8. Effective tension area EN 1992-1-1 7.3.2(3), Fig. 7.1

The crack width depends on the concrete around the tension bars. Its depth hc,eff is the least of 2.5 (h − d), (h − x) / 3 and h / 2, with x from the quasi-permanent case. Only the 3Y20 bottom bars lie in it.

h_c,eff = min(2.5 × 50, (500 − 169.88) / 3, 500 / 2) = min(125.0, 110.04, 250.0) = 110.04 mm A_c,eff = 300 × 110.04 = 33012 mm² ρ_p,eff = A_s / A_c,eff = 942.5 / 33012 = 0.02855

9. Strain difference EN 1992-1-1 7.3.4(2), eq. 7.9

εsm − εcm is the steel strain less the help the concrete gives between cracks (tension stiffening). kt = 0.4 for long-term load, fct,eff = fctm, and here αe = Es / Ecm = 6.091. It may not be less than 0.6 σs / Es.

ε_sm − ε_cm = [σ_s − k_t f_ct,eff / ρ_p,eff × (1 + α_e ρ_p,eff)] / E_s = [242.33 − 0.4 × 2.896 / 0.02855 × (1 + 6.091 × 0.02855)] / 200000 = 0.9735 × 10^-3 0.6 σ_s / E_s = 0.6 × 242.33 / 200000 = 0.7270 × 10^-3 → use 0.9735 × 10^-3

10. Crack spacing and crack width EN 1992-1-1 7.3.4, eq. 7.11, 7.8

The bar spacing (100 mm) is below 5 (c + φ/2) = 225 mm (φ = 20 mm, the bar size), so eq. 7.11 applies (not 7.14). k1 = 0.8 (high bond bars), k2 = 0.5 (bending), k3 = 3.4 and k4 = 0.425 (recommended values). c = 35 mm is the cover input of the calculator; with the Y20 centres 50 mm up the clear cover is 40 mm, so 35 mm gives a slightly smaller sr,max. wmax = 0.3 mm is a practice value chosen by the user (the calculator's default, from Table 7.1N).

s_r,max = k3 c + k1 k2 k4 φ / ρ_p,eff = 3.4 × 35 + 0.8 × 0.5 × 0.425 × 20 / 0.02855 = 238.09 mm w_k = s_r,max (ε_sm − ε_cm) = 238.09 × 0.9735 × 10^-3 = 0.232 mm ≤ 0.3 mm OK

11. The calculator's answer

The calculator, with the same inputs, gives (engine 1.1.0): characteristic x = 111.3 mm, σc = 16.67 MPa, σs = 308.8 MPa; quasi-permanent x = 169.9 mm, σc = 8.04 MPa, σs = 242.3 MPa; wk = 0.232 mm, and PASS. The hand calculation gives x = 111.3 / 169.9 mm, σc = 16.67 / 8.04 MPa, σs = 308.8 / 242.3 MPa and wk = 0.232 mm. The engine finds the cracked strain plane numerically on 1 mm strips, so the last digit can differ. Raise the quasi-permanent moment to 120 kNm in the calculator and watch the crack width grow.

Run this example yourselfOpen the STATIX RC section SLS calculator. These are the calculator's default inputs, so it opens on this example. Change any value and the result updates, with every check and a calc sheet.
Open the RC section SLS calculator

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.

Early access

Be first to use STATIX 3D.

STATIX 3D is still being built. Join the early-access list and we will tell you when it is ready for testing. One confirmation now, one message then.

Get early access