STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

Retaining wall along its length to SANS 10100

A 12 m long reinforced concrete cantilever wall holds back 3 m of granular fill with a 10 kPa surcharge. The wall is designed segment by segment along its length: earth pressure, sliding, overturning and bearing (as global factors of safety and with partial factors), overall stability, the stem and base bars, and early-age cracking. Every result below is what the STATIX retaining wall 3D calculator reports for the values in step 1.

1. The problem

InputValue
Wall type, codecantilever, SANS 10100-1
Length / retained height (top of wall to the base underside)12 m / 3 m
Stem / base thickness300 / 400 mm
Toe / heel700 / 2 000 mm (base width 3.0 m)
Front soil over the base500 mm
Backfill φ′ / γ30° (given) / 18 kN/m³
Surcharge10 kPa
Allowable bearing pressure150 kPa (given)
Founding soil under the base: φ′ / γ30° / 18 kN/m³ (given)
Base friction coefficient0.45
Passive resistance in front of the toeignored (the default)
Water behind the wallnone
Seismicnone (given)
fcu / fy; cover30 / 450 MPa; 50 mm (60 mm the base)
Early-age temperature drop T120 °C (given)

The six values marked given are the ones the calculator asks you to confirm for your site. Leave them as it fills them and a passing wall reads REVIEW, not PASS (step 6).

2. Earth pressure

A cantilever wall can move a little, so the backfill is in the active state. With Rankine’s coefficient:

Ka = (1 − sin 30°) / (1 + sin 30°) = 1/3 soil at the base: Ka γ H = 18 × 3 / 3 = 18.0 kPa (a triangle); surcharge: Ka q = 3.33 kPa (uniform) force on the wall: ½ × 18.0 × 3 + 3.33 × 3 = 27.0 + 10.0 = 37.0 kN/m

3. Stability: sliding, overturning and bearing

The wall must not slide, tip or press the soil too hard. The calculator checks these twice: with global factors of safety (SANS 10160-5) and with partial factors on the actions and the soil (the GEO set: G 1.0, Q 1.3, the soil strength factored).

sliding resistance = μ × permanent weight = 0.45 × (19.5 stem + 30.0 base + 93.6 soil on the heel) = 0.45 × 143.1 = 64.4 kN/m FoS = 64.4 / 37.0 = 1.74 ≥ 1.5

The surcharge on the heel is not counted as resisting: it is a variable load and may be absent. The passive resistance of the soil in front of the toe is not counted either: that soil can be dug away later, so the calculator ignores it unless you include it. Included, it would add 6.75 kN/m here.

CheckResultUse
Sliding, partial factorsgoverns the wall95 %
Sliding, global FoS1.74 against 1.586 %
Overturning, global FoS5.92 against 2.034 %
Bearing pressureqmax 55.8 kPa against 150 kPa37 %
Bearing, partial factors—46 %
Eccentricitye 0.055 m ≤ B/6 = 3.0/6 = 0.500 m (no lift at the heel)11 %
Overall stability (slip circle)—69 %

Sliding governs, as it often does for a cantilever wall on granular soil. With a 1.8 m heel the same wall would need the passive soil to pass; the 2.0 m heel carries more soil on the base and passes without it. A shear key or a rougher founding layer are the other ways to raise the sliding resistance.

4. The stem and the base

The stem is a cantilever from the base; the toe and the heel are cantilevers from the stem. Without links, the shear decides more often than the bending:

CheckUse
Stem deflection (span / depth, SANS 10100-1 4.3.6)91 %
Heel shear (4.3.4)70 %
Stem shear43 %
Toe shear36 %
Crack control (bar spacing)33 %
Stem bending / heel bending / toe bending14 % / 16 % / 3 %

5. Early-age heat and shrinkage

The stem is cast on a base that has already hardened, so the base holds it as it cools and shrinks. EN 1992-3 Annex M:

ε = Rax (αc T1 + εca) = 0.5 × (10 × 10−6 × 20 + 50 × 10−6) = 125 × 10−6 horizontal Y10 @ 200 each face: wk = 0.17 mm ≤ 0.30 mm (EN 1992-1-1 Table 7.1N), 57 %

6. Result, and what REVIEW means

With the six values given, the wall reads PASS; the governing row is sliding with partial factors (95 %). Leave them as the calculator fills them and the same wall reads REVIEW: it names the backfill friction angle and the other values it assumed, and asks you to confirm them. REVIEW is never shown as PASS.

7. Do it in STATIX

Open the retaining wall 3D calculator, type the values in step 1 and compare the rows. For a single cantilever section with its full hand calculation, see the cantilever retaining wall example.

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.