STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

RC section under biaxial bending to EN 1992-1-1

A column section under axial force and bending about both axes has an inclined neutral axis. Here strain compatibility with the rectangular stress block of EN 1992-1-1 is worked by hand for a 400 × 600 mm section with eight Y20 bars. The hand calculation is checked against the STATIX general RC section calculator.

1. The problem

InputValue
Sectionrectangle b × h = 400 × 600 mm
Bars8 Y20: 3 along b and 3 along h (corners counted once), cover 40 mm to the bar surface
CodeEN 1992-1-1, α_cc = 0.85
Concrete / steelf_ck = 30 MPa, f_yk = 500 MPa
ActionsN_Ed = 800 kN (compression), M_x = 150 kNm, M_y = 60 kNm

2. The method EN 1992-1-1 6.1, 3.1.7(3)

Plane sections stay plane. At the ultimate limit state the most compressed fibre is at εcu3 = 0.0035. The concrete is a rectangular block of depth λ x = 0.8 x at η fcd (η = 1.0 for fck ≤ 50 MPa), concrete in tension carries nothing, and the steel is elastic up to fyd. For biaxial bending the neutral axis is inclined: the calculator finds the depth that carries NEd and the angle that makes the resisting moment point the same way as the applied moment.

3. Materials EN 1992-1-1 3.1.7(3)

αcc = 0.85 is the calculator's default: a practice value, the National Annex sets it (SANS 51992 uses 1.0). γc = 1.5 and γs = 1.15.

f_cd = α_cc f_ck / γ_c = 0.85 × 30 / 1.5 = 17.00 MPa f_yd = f_yk / γ_s = 500 / 1.15 = 434.78 MPa, ε_yd = f_yd / E_s = 0.00217 ε_cu3 = 0.0035, λ = 0.8, η = 1.0

4. Section and bars

The origin is at the centre of the section, x to the right, y up. The bar centres are 50 mm (cover + half the bar) in from each face. Moments are taken about the centroid, which is the centre here. Mx positive puts the +y face in compression, My positive the +x face.

A_c = 400 × 600 = 240000 mm² A_s = 8 × π × 20² / 4 = 8 × 314.16 = 2513.3 mm² bars at x = −150, 0, 150 on y = ±250, and at x = ±150 on y = 0
neutral axisblock 0.8 c12345678xy8Y20: teal in compression, red in tension

5. Axial resistance limits EN 1992-1-1 6.1

In pure compression the strain is εc3 = 0.00175 everywhere, so the steel works at min(fyd, Es εc3) = 350 MPa. In pure tension only the steel works, at fyd. NEd = 800 kN lies between the two.

N_Rd,max = f_cd (A_c − A_s) + A_s × 350 = 17.00 × (240000 − 2513.3) + 2513.3 × 350 = 4916.9 kN N_Rd,min = −A_s f_yd = −2513.3 × 434.78 = -1092.7 kN

6. The neutral axis EN 1992-1-1 6.1

This step is NOT worked by hand: the angle and the depth of the neutral axis are taken from the calculator. They come from two nested searches (the depth c that makes the internal force equal NEd, and the angle θ that makes MRd,y / MRd,x = My / Mx), which is not practical by hand. Every step after this one is worked by hand, and it shows that this axis does carry NEd = 800 kN. θ is the direction of the compression side, measured from +x; s is the distance of a point from the most compressed corner (200, 300), measured along θ.

θ = 0.78507 rad = 44.98°, c = 303.34 mm most compressed corner: s_max = 200 cos θ + 300 sin θ = 353.53 mm depth of the section along θ: h_θ = 400 cos θ + 600 sin θ = 707.1 mm > c, so ε_cu3 at the corner applies (no pivot at ε_c3, 6.1(5))

7. Concrete compression block EN 1992-1-1 3.1.7(3)

The block reaches 0.8 c in from the corner. At this angle it cuts the top face and the right face, so it is a right triangle with its legs along those faces.

0.8 c = 242.67 mm leg along the top: L_x = 0.8 c / cos θ = 343.07 mm; leg down the side: L_y = 0.8 c / sin θ = 343.30 mm A_block = L_x L_y / 2 = 58888 mm², centroid at (200 − L_x/3, 300 − L_y/3) = (85.64, 185.57) mm F_c = f_cd A_block = 17.00 × 58888 / 1000 = 1001.1 kN

8. Bar strains and forces EN 1992-1-1 6.1

Each bar's strain follows from the straight strain line: ε = εcu3 (c − s) / c, compression positive. The stress is Es ε, capped at ± fyd = ± 434.8 MPa. A bar inside the block takes the place of block concrete, so fcd is taken off its stress. Each bar has As = 314.16 mm².

s = s_max − (x cos θ + y sin θ), ε = 0.0035 (303.34 − s) / 303.34 bar 1 (-150, -250): s = 636.3 mm ε = -0.00384 σ = -434.8 MPa F = -136.6 kN bar 2 (-150, 250): s = 282.9 mm ε = 0.00024 σ = 47.1 MPa F = 14.8 kN bar 3 ( 0, -250): s = 530.2 mm ε = -0.00262 σ = -434.8 MPa F = -136.6 kN bar 4 ( 0, 250): s = 176.8 mm ε = 0.00146 σ = 292.0 MPa − f_cd = 275.0 F = 86.4 kN bar 5 ( 150, -250): s = 424.1 mm ε = -0.00139 σ = -278.8 MPa F = -87.6 kN bar 6 ( 150, 250): s = 70.7 mm ε = 0.00268 σ = 434.8 MPa − f_cd = 417.8 F = 131.3 kN bar 7 (-150, 0): s = 459.6 mm ε = -0.00180 σ = -360.7 MPa F = -113.3 kN bar 8 ( 150, 0): s = 247.4 mm ε = 0.00065 σ = 129.0 MPa F = 40.5 kN

9. Sum of forces and moments

Add the block and the eight bars. The axial force must come back to NEd; the moments about the centroid are the resisting moments, and their ratio must equal My / Mx = 0.400.

N_R = 1001.1 + (-201.1) = 800.0 kN = N_Ed 800 kN M_Rd,x = F_c y_c + Σ F y = 1001.1 × 185.57 / 1000 + (148.30) = 334.07 kNm M_Rd,y = F_c x_c + Σ F x = 1001.1 × 85.64 / 1000 + (47.89) = 133.63 kNm M_Rd,y / M_Rd,x = 133.63 / 334.07 = 0.400

10. Utilisation EN 1992-1-1 6.1

The resisting moment and the applied moment point the same way, so their lengths can be compared directly at NEd.

M_Rd = √(334.07² + 133.63²) = 359.81 kNm |M_Ed| = √(150² + 60²) = 161.55 kNm utilisation = 161.55 / 359.81 = 0.449 ≤ 1 OK

11. The calculator's answer

The calculator, with the same inputs, gives (engine 1.2.1): NRd from -1093 to 4917 kN, MRd,x = 334.1 kNm, MRd,y = 133.6 kNm, MRd = 359.8 kNm, utilisation 0.449 and PASS. The hand calculation from its neutral axis gives N = 800.0 kN, MRd = 359.8 kNm and utilisation 0.449. Change My in the calculator and watch the neutral axis turn.

Run this example yourselfOpen the STATIX general RC section calculator. These are the calculator's default inputs, so it opens on this example. Change any value and the result updates, with every check and a calc sheet.
Open the general RC section calculator

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.

Early access

Be first to use STATIX 3D.

STATIX 3D is still being built. Join the early-access list and we will tell you when it is ready for testing. One confirmation now, one message then.

Get early access