STATIX SANS · Eurocode · BS 8110 Find a calculator…48 Start free trial
Learn · worked example

Box culvert to TMH7

A single-cell reinforced concrete box culvert, 2.4 m wide and 1.8 m high inside, carries a road over 0.8 m of fill. TMH7 gives the traffic loads that spread through the fill; the box works as a closed frame; the base must not overload the ground; and the wing walls at each end are small retaining walls. Every result below is what the STATIX box culvert calculator reports for the values in step 1.

1. The problem

InputValue
Cells, clear span x height1 cell, 2 400 x 1 800 mm
Walls / top slab / bottom slab250 / 300 / 350 mm, haunches 150 mm
Barrel length / skew12 m / 0°
Fill over the top slab0.8 m, 1 900 kg/m³, TMH7 type I
TrafficTMH7 NA (2 notional lanes, carriageway 7.4 m) and NB36
Allowable bearing pressure150 kPa (given)
Ground water above the invert0.3 m (given)
Scour depth at the ends600 mm (given)
Base friction under the wing walls0.45 (given)
Founding soil friction angle under the wings30° (given)
Concrete / steelC30/37, fy 450 MPa

The five values marked given are site values the calculator asks you to confirm. Leave them as it fills them and a passing culvert reads REVIEW, not PASS (step 5).

2. Loads through the fill (TMH7)

The fill weighs on the top slab, and the wheel loads spread through it. Two of the TMH7 load cases, by hand:

fill (TMH7 2.3.3.2): g2 = 10 ρ h × 10−3 = 10 × 1 900 × 0.8 × 10−3 = 15.2 kPa NA (iii), two 100 kN wheels, each spread over a circle R = h + 0.2 = 1.0 m: p = 100 / (π × 1.0²) = 31.8 kPa

The calculator runs every TMH7 case (NA uniform and strip, the NA wheels, NB36 placed for the worst effect, the earth on the walls with and without its relieving part) and factors them for the ultimate and the serviceability states. On the ultimate effects it applies γf3 = 1.10 (TMH7 Part 3 2.2.2).

3. The box as a frame

The slabs and walls form a closed frame, so the corners are continuous and the moments share between span and corner. The governing rows:

CheckBars and resultUse
Bottom slab shear (no links, SANS 10100-1 4.4.5.2)V 116.6 kN/m at about d from the joints, d 267 mm99.6 %
Bottom slab bending, inside faceY12 @ 150 (754 mm²/m), d 294 mm98.7 %
Top slab shearV 124.9 kN/m, d 217 mm95.0 %
Bottom slab crack width, inside (TMH7 Part 3 3.8.8.2)—95.0 %
Top slab bending, inside faceY12 @ 100 (1 131 mm²/m), d 244 mm; the governing case is NA (iii) along the barrel at 0.8 m cover69.2 %

The slabs have no links, so the shear decides their thickness; the calculator takes no enhancement near the supports, on the safe side. A thicker bottom slab is the usual answer when the shear is this close.

4. The ends: wing walls

Each of the four wing walls is a small retaining wall, checked like one, with the soil over the toe ignored for scour and the ground water behind it (1.05 m above the base, from the ends’ ground-water level). The calculator gives the wings a 6.4 m base. Here the wing heel shear governs the whole culvert, 99.7 %, just ahead of the bottom slab shear; then the stem deflection (span / depth) 98.3 % and the overall stability (slip circle) 97.7 %. Sliding with partial factors is 66 %: it counts only the passive resistance on the face of the shear key (14.6 kN/m), the key’s own resistance; without it the row would read 74 %. Several of these rows sit close to 100 % by design: the calculator picks the lightest bars that pass, so a thicker section simply gets fewer bars. The wing rows are tight because of the water behind the walls; the calculator does not model drainage, which in practice is the usual way to relieve them (weep holes and a drain behind the wing).

5. Result, and what REVIEW means

With the five site values given, the culvert reads PASS; the governing row is the wing heel shear (99.7 %), with the bottom slab shear (99.6 %) next. Leave them as the calculator fills them and the same culvert reads REVIEW: it names the allowable bearing pressure and the other values it assumed and asks you to confirm them. REVIEW is never shown as PASS.

6. Do it in STATIX

Open the box culvert calculator, type the values in step 1 and compare the rows. Sign in to see every check, step by step, on the calc sheet.

A worked example for learning, not a design. Check every value against the current code and your own project, and have the design checked and signed by a registered professional engineer.